Yosef Hefetz • November 13, 2026

Gas Fireplace Pilot Won't Stay Lit? What Makes It Drop Out

The first sign most homeowners notice isn't rain at all. It's a faint tapping behind the damper during a storm, or a ring of gray water sitting in the firebox the next morning with no obvious source, because the roof is dry and the gutters are clear. The chimney itself is the leak. What that one morning shows is only the first frame of a much longer sequence, though: an open flue doesn't do the same damage on night one that it does after three winters of the same neglect, and which stage you're looking at changes what actually needs fixing.



What follows is the order in which damage actually occurs, from the top of the stack down to the framing behind the wall, and from the first storm to years of neglect. This is about a flue with no cap at all; a cap that's present but too small or the wrong shape for what it's covering is a separate problem with its own failure pattern.

Factor Older/historic masonry Modern masonry
Mortar binder Lime-based, low or no Portland cement Portland-cement-based, harder curing
Mortar flexibility Softer, some self-healing of hairline cracks Rigid once cured, cracks stay cracked
Brick type Handmade or soft-mud, lower fire temperature Extruded, wire-cut, higher fire temperature
Brick porosity More absorbent, prone to spalling Denser, less water uptake
Typical liner status Often unlined, undersized, or original clay tile Liner sized and installed to current standards
Repair priority Match mortar chemistry, not just color Standard modern mortar mixes generally compatible
Common failure pattern Brick face spalling; joint self-healing can mask real deterioration Joint cracking tends to precede brick damage

Older chimneys were often built on shallower footings than current standards call for, and after decades of ground movement and the chimney's own weight, some settling is common: a slight lean, a visible gap where the chimney meets the roofline, or a stair-step crack pattern following the mortar joints diagonally. A small, stable lean or an old, dormant crack isn't automatically an emergency, but telling "old and stable" from "active and worsening" benefits from a hands-on inspection rather than a guess from the ground.

.sweep-table-wrapper{ width:100%; margin:15px 0; overflow-x:auto; } .sweep-table{ width:100%; border-collapse:collapse; min-width:650px; } .sweep-table th{ background:#E31013; color:#fff; text-align:left; padding:12px 14px; font-size:19px; font-weight:700; border:1px solid #000; } .sweep-table td{ background:#F5F5F5; color:#111; padding:10px 14px; font-size:17px; border:1px solid #000; vertical-align:top; line-height:1.75; } .sweep-table td:first-child{ font-weight:700; width:33%; } .sweep-table th:nth-child(2), .sweep-table th:nth-child(3){ width:33.5%; } @media(max-width:768px){ .sweep-table th, .sweep-table td{ padding:10px; font-size:14px; line-height:1.6; } }

A technician can often get a first read on mortar type without lab testing. Dragging a metal key or nail across a joint that leaves a visible scratch and a little powder points toward a softer, lime-rich mix, while a joint that resists scratching and holds a sharp edge points toward a harder, Portland-heavy mix. This test doesn't replace a proper inspection or lab analysis of the actual composition, but it's a useful first check before assuming a chimney can be treated like standard modern construction.

The damper is the movable plate that opens and closes the path between the firebox and the flue above it. Traditional dampers are a hinged metal flap mounted at the throat, right in front of the smoke shelf at essentially the same level; newer systems often use a top-mount damper instead, a sealing plate at the very top of the flue operated by a cable or lever from the firebox. The damper's job: it closes off the flue when there's no fire burning, so conditioned indoor air doesn't pour straight up the chimney, and it opens fully to let smoke and gases draft out when you do have a fire going. A damper that won't seat properly, whether warped, rusted, or coated in old creosote, wastes energy and can also affect how well a fireplace drafts once lit.

Hearth Extension

When a Post-Renovation Inspection Is (and Isn't) Warranted

The hearth extension, the noncombustible floor pad in front of the firebox opening, catches stray ash, bark, splinters, and the occasional ember that pops clear of the fire. A quick vacuum with a shop vac or a canister vacuum's brush attachment once a week during active burning keeps this debris from working into carpet fibers or wood flooring at the hearth's edge, and it's your chance to glance for embers that landed outside the firebox and cooled without your noticing. Check that logs, kindling, and any decorative items on the mantel or nearby furniture haven't crept closer to the opening than the several feet of clearance most fireplace manufacturers and fire-safety groups recommend as a baseline. This is also a good moment to make sure nothing- a rug corner, a stack of kindling, a pet bed- has migrated into that clearance zone since the last time you checked.

Waterproofing is a preventive and protective treatment for masonry that's fundamentally in good shape but exposed to the elements, not a repair for masonry that's already showing damage. If the brick or mortar has visible deterioration such as spalling, crumbling joints, or a cracked crown, that damage needs to be addressed on its own terms before waterproofing goes on top of it, since sealing over a compromised surface just locks moisture problems in rather than out. Once repairs are handled, waterproofing is a reasonable next step for extending the life of the masonry and reducing how much water it absorbs going forward, particularly on a chimney with no roof overhang or nearby shelter shielding it from direct weather. It's also a sensible addition anytime a chimney gets rebuilt or has significant tuckpointing done, since new mortar is at its most porous in the first year or two.

Reading Your Results

Red Flag What a Legitimate Technician Does Instead
Rock-bottom advertised price, then "mandatory" add-ons once the tech is on-site States the base price and what could change it before the appointment; add-ons are optional and explained, not sprung
Claims of imminent fire or CO danger with no proof Shows photos or video tied to the specific finding, or explains it in plain language you can follow
Vague or evasive about certification and training Names the certifying body (e.g., CSIA), can describe what the credential covers
No mention of insurance, no findable business address Carries liability coverage and can provide proof if asked; operates from a verifiable business
Refuses to show camera footage or "you wouldn't understand it" Walks you through findings, translating technical detail into plain terms
"This price is only good if you sign today" Gives you time to think it over; urgency is reserved for genuine active hazards, not routine repairs
Unmarked vehicle, cash-only, no paperwork Provides a written estimate or service report you can keep
```

Checking a company's standing takes a few minutes and heads off most of the above. Look up online reviews for specific complaints, not just the star rating. Confirm the business has a physical address you can find, not just a phone number. Ask about certification and insurance before scheduling, not after a technician is in your driveway. If your state or municipality licenses chimney sweeps, that license number should be something the company provides without hesitation, and a short phone call asking directly usually tells you a lot from how readily it gets answered.

Set the red flags aside for a moment, because it helps to know what you're aiming for, not just what you're avoiding. A technician doing this job the right way walks you through the visit almost like a translator: here's what I found, here's what it means, here's what happens if it's left alone versus addressed. If a camera scan turns something up, you see the footage, or at minimum get a clear description tied to a specific location in the flue, not a vague reference to "damage up there." Recommendations get written down, often in a service report you keep, so you have a record to compare against next year rather than a verbal claim you have to just remember and trust.



Pricing is explained before work starts, and changes to that price come with a reason you can follow, not a mandatory bundle sprung mid-visit. And critically, nothing about the timeline pressures you into deciding on the spot. A technician confident in the finding doesn't need you to decide before he's back in the truck.

Symptom Likely Cause What to Do
White, chalky staining on the brick Efflorescence: water moving through porous masonry and leaving mineral deposits behind as it evaporates Leak detection to find the entry point, then a breathable waterproofing treatment
Rust stains or flaking metal around the damper or firebox Water reaching the damper assembly, firebox, or metal chimney components Damper inspection and repair, plus a check of the cap and crown for openings
Crumbling, flaking, or pitted brick faces (spalling) Repeated saturation, worsened by freeze-thaw cycling, pushing the brick's face apart from the inside Masonry repair, or a partial to full rebuild in advanced cases
Cracks or erosion in the chimney crown The concrete or mortar wash at the top of the stack has failed, letting rain track straight into the flue Crown repair or replacement, paired with a properly fitted cap
Water stains on the ceiling or wall near the fireplace Flashing where the chimney meets the roofline has separated, corroded, or was installed poorly Leak detection to confirm the source, then flashing repair
A musty, damp smell from the fireplace, especially after rain Trapped moisture in the flue liner, firebox, or smoke chamber that never fully dries out A Level 2 inspection of the interior, plus waterproofing if the masonry is porous
```

What Comes After the Inspection

Load the Firebox Right-Sized

If more than one of these looks off at the same time, a technician typically checks all three anyway, since they sit inches apart around a single roof penetration and a problem at one often points to strain on another.

WARNING: Climbing onto a steep or wet roof to inspect these parts up close carries a real risk of falling. Identify what you can see from the ground, and leave close-range inspection to a professional. (336) 604-6711.

Fuel Type Core Upkeep Tasks Typical Frequency Who Handles It
Wood-burning Creosote/soot sweep, flue liner inspection, cap and crown check, damper seal, ash removal Sweep and inspection at least annually (NFPA 211 baseline); ash removal as needed between burns Certified sweep for the flue/liner/cap; ash removal is a homeowner task
Gas fireplace/insert Pilot or ignition system check, burner and orifice cleaning, vent inspection, glass gasket check, log placement Annual professional inspection; light dusting of the surround as needed Professional for burner, venting, and ignition components; surface dusting is a homeowner task
Electric Dust heat exchanger and fan intake, wipe glass front, replace LED/bulb occasionally Dusting every few weeks during regular use; bulb/LED replacement over a period of years Homeowner task for routine upkeep; component failures go to appliance/electrical repair, not chimney service
```
Fuel Type Core Upkeep Tasks Typical Frequency Who Handles It
Wood-burning Creosote/soot sweep, flue liner inspection, cap and crown check, damper seal, ash removal Sweep and inspection at least annually (NFPA 211 baseline); ash removal as needed between burns Certified sweep for the flue/liner/cap; ash removal is a homeowner task
Gas fireplace/insert Pilot or ignition system check, burner and orifice cleaning, vent inspection, glass gasket check, log placement Annual professional inspection; light dusting of the surround as needed Professional for burner, venting, and ignition components; surface dusting is a homeowner task
Electric Dust heat exchanger and fan intake, wipe glass front, replace LED/bulb occasionally Dusting every few weeks during regular use; bulb/LED replacement over a period of years Homeowner task for routine upkeep; component failures go to appliance/electrical repair, not chimney service
```

If they won't come back or can't explain the fit, a second CSIA-certified sweep can inspect cap and flue together and say which is at fault.

What a Previous Repair Substituted

You are not going to read the assembly from an armchair, but a few things carry out into the room, and they are the reasons to pick up the phone.



A door that will not latch without lifting or leaning on it has moved. A dark line at a panel joint that was not there last year, visible with a flashlight from outside the opening, is a gap opening up. Rust-colored staining in the floor of a cold firebox after heavy rain means water is arriving where it should not be. A smell of old smoke in the room while nothing is burning points to a flue that is not carrying the way it did. A metallic rattle from the chimney in wind should be reported exactly as you heard it.


None of these will tell you which component moved, and none of them need to. They tell you when to call. Emergency work is covered around the clock, and ordinary scheduling is fast, so a fireplace that has started behaving differently does not have to wait.

Construction Method How the Joint Holds Where Moisture Can Sit What Changes Over Time
Continuous weld Fused along the full seam No gap along the seam Rigid; movement handled by design, not the joint
Spot or resistance weld Fused at discrete points The lap between weld points Single welds can release with no visible change
Rivet or screw assembly Clamping at each fastener The lap joint and fastener hole Joints loosen under vibration and thermal cycling

A cap can land in both condition columns at once, and every finding stands on its own rather than being averaged into a verdict for the assembly.

Tiles Larger Than the Catalog Goes

Telling the metal parts apart up there, cap against chase cover against storm collar, is set out in this site's comparison of chimney caps and chase covers.

WARNING: A shroud whose maker cannot be identified leaves a technician with no description at all of the termination it encloses. Expect that question first at a factory-built top, ahead of any conversation about matching the finish or the metal.

Manufacturer-Matched Cap Universal Cap Aftermarket Decorative Shroud
Specified by Model and part number for your system Outside diameter and pipe class Chase opening and appearance wanted
How it attaches Engages the pipe series' own locking detail Clamp band or slip fit sized to diameter Fastens to the chase cover or chase framing
What the system's literature says Names this part for this system Silent on your system by name Named only if the system's own maker built it
What is known about the top afterward The arrangement matches the one specified Dimension known; arrangement not The enclosure has changed, and its behavior is unknown
Where it is sourced The system's maker, or whoever supports the series A general chimney supplier's catalog A sheet metal shop or shroud fabricator
What a technician confirms on site Part number read against the data plate Diameter, pipe class, and that the clamp seats How it is fastened and how it sits

What "Universal" Covers and What It Stays Silent About

WARNING: Water trapped inside a chase wall can soak the framing and sheathing for months before any sign appears on the visible surface. A ceiling stain or musty smell near a decorative chase is worth having checked rather than watched.

Flies that keep showing up in the same room usually aren't the actual problem. They're a sign pointing at something else, sitting somewhere you can't see from where you're standing. Chasing the window, the screen, or the baseboard treats the sign instead of the source. The flue is worth ruling out first, not last, especially once every other explanation in the room has already come up empty.

An alarm is a last line of defense, not a way of finding a venting problem. The marks at the draft hood come first.

WARNING: If a report describes a crack or opening into the flue itself, don't operate the fireplace or wood stove while you wait on a second opinion. A second scope can wait; smoke or gas escaping through a breach in the liner can't.

WARNING: Discolored drywall, scorched trim, or a resinous smell near the pipe means heat is reaching something it should not. Stop using the stove and have the assembly inspected before the next fire; do not reposition pipe or add shielding yourself.

None of this depends on the calendar. A system that has sat idle through warm months is easier to open up and examine closely, while one in regular use shows heat effects and staining that an idle assembly hides. Both are good conditions to inspect in, for different reasons.

Anything with a burner in it counts: a water heater, a boiler, a furnace in a crawlspace nobody opens, a gas log set in a room nobody sits in. Until each one has been traced to the shaft that carries its exhaust, the flue in question has not been shown to be out of use.

Approach What It Settles What It Leaves Open
Leave it as it is Nothing. The shaft stays available if an appliance is ever added back Weather, air movement, falling debris, and the same unanswered question for whoever owns the house next
Close the top Weather and most of what comes in from above The interior condition, the openings lower down, and any assumption made about what the shaft carries
Take it out of service The shaft's status, handled as a change to the system by a professional and written down as such Nothing, provided the venting question was answered first
Consideration Open Masonry Fireplace Insert Set in the Same Opening
What carries the exhaust The full masonry flue as built A continuous liner running to the appliance
Air supply Room air pulled freely through the opening A restricted, controlled combustion air feed
Exhaust behavior Hot, diluted, fast Cooler and slower, so condensation and deposits form more readily in an oversized space
Path required Nothing beyond the masonry itself An uninterrupted run, top to appliance, with no section left out
Damper Opened and closed as needed The plate normally sits in the path the liner has to take
How it is judged Condition and cleanliness Measured on site and compared to the appliance manufacturer's own venting instructions

A pre-insert evaluation produces camera footage of the flue, photographs of the throat, smoke chamber, firebox, and hearth, and on-site measurements. Those photographs are supplied for your own records, so the file stays with the house rather than living in someone's memory. Measurements are taken at the chimney, never assumed from a phone description, because the tightest point in a flue is not visible from the living room.



Those three things do most of the work of choosing an appliance. They say which units your chimney can accept and which it cannot. They put any repairs that need to happen first in order. And they give whoever eventually fits the unit a set of real dimensions to work from, so the appliance and the chimney are matched on paper before they are matched in the room.


The dimensions are the part that saves the most trouble. An insert chosen against a measured flue arrives at a chimney already known to take it, and the fitting day is an installation and nothing more. An insert chosen against a guess arrives, with the fitting still an open question; by then, the unit is in the driveway, and the chimney has the last word anyway.

WARNING: If a firebox photo shows stored wood, cardboard, or other combustible material inside or against the opening, that's a hazard in its own right, separate from any structural issues. Clear the firebox before lighting any fire.

TIP: A camera inspection of the flue produces a set of still photographs you keep whether or not any repair follows, so the condition of the liner on the day the work next door started stays on record.

A standing pilot on a gas fireplace keeps itself burning through a small closed loop. The pilot flame plays over the tip of a thermocouple, or on some fireplaces, a thermopile, and that heat makes the sensor produce a tiny electric current. The current travels back to the gas valve, energizes an electromagnet inside it, and the magnet holds the safety seat open so gas can continue reaching the pilot. Take the heat away and the current fades, the magnet lets go, and a spring closes the seat. That shutdown is deliberate. The valve has no way to tell a flame that went out for a harmless reason from one that went out while gas kept flowing, so it stops the gas in both cases. A pilot that keeps dropping out is the safety system doing the one job it was built for, and a good diagnosis finds where the loop is breaking without ever overriding it.



Heat can go missing at the sensor, in the flame, in the air around the flame, or in the gas feeding it, and the moment the pilot quits says a good deal about which one.

Reading the Pattern of the Dropout

Each timing pattern in this pairing matches a part of the loop where heat, flame, or gas can fall short.

When or how the pilot drops out Where the loop is likely breaking
Goes out the moment the knob is released The sensor is producing too little current, or its tip sits outside the flame
Lights and holds a few minutes, then drops A worn sensor that starts strong and fades, or a flame that shrinks or wanders once it settles
Goes out when the main burner comes on Supply pressure sagging as the burner opens, or burner flame and air pulling the pilot flame off the sensor
Goes out on windy days Air moving through the vent disturbing the pilot flame (vented units)
Pilot flame small, yellow, or lifting off the sensor A partly blocked pilot orifice, low supply pressure, or a disturbed air supply
Goes out after the fireplace sat unused Dust or debris narrowing the pilot orifice or tube

Two rows can describe one fireplace. A sensor that has lost some output still holds while the flame is perfect and gives up the first time it is anything less, so the flame gets examined before any part is condemned.

The Thermocouple or Thermopile in the Flame

A thermocouple is two different metals joined at a tip. Heat that junction, and a small voltage appears across it; that voltage is the entire signal the valve relies on. The output is modest by design, since it only has to hold a magnet that was pulled in by hand when the knob was pressed, leaving little margin for error.



A thermopile is a set of those junctions wired together, so the same flame produces more current. On some fireplaces, the thermopile runs the main burner valve while a separate thermocouple guards the pilot; on others, a single thermopile handles both jobs.


Two things go wrong with the sensor itself. The first is wear. Constant heat oxidizes and thins the metal at the tip over years of service, and its output drifts down with it. A worn sensor can look intact and still fall short.


The second is position. The pilot hood shapes the pilot flame and aims it so the sensor tip sits inside the flame, wrapped by it rather than grazing its edge. A bracket nudged during a cleaning, a log or a clump of ember material set against the pilot hood, or a hood knocked slightly askew can leave the tip licking at the margin of the flame.

A Weak or Dirty Pilot Flame

A healthy pilot flame is steady and blue, and it is sized and directed well enough to envelop the sensor tip. It is fed through a pilot orifice, a very small drilled opening, and a small particle is enough to narrow that opening. A narrowed orifice passes less gas, and the flame shrinks, softens, and turns lazy and yellow at the tips. A yellow flame is burning incompletely and can leave its own film on the sensor.



On some pilot assemblies, the flame also draws a small amount of air through small openings near the orifice, so the gas burns cleanly. Lint or dust across those openings starves the mixture of air and yellows the flame the same way. A fireplace left off for a stretch can pick up dust and spider webbing in the pilot tube, which is one more way the passage narrows.


A flame that lifts off the hood and floats is a different signal. Lifting occurs when the flame is pushed away from its base, either by gas pressure exceeding the orifice setting or by air moving across the burner, and a lifted flame can hover just clear of the sensor while appearing large and healthy.


Vent-free log sets use a different pilot design: an oxygen-depletion sensor that shuts the pilot down on purpose when room conditions change, and a dropout on one of those is its own diagnosis.

Draft and Air Moving Across the Pilot

This one applies to vented units. Wind or house pressure that drives air down a flue can push a pilot flame sideways off its sensor, the same reversal that sends wood smoke back into a room.



The air inside the room matters too. A vented log set sits in an open firebox with its damper clamped open, allowing room air to reach the pilot directly. A ceiling fan, a heating or cooling register aimed toward the hearth, or a door that sends a draft across the firebox each time it opens can all bend a small flame. Moving the pilot flame a short distance is enough to cool the sensor.

Gas Supply to the Pilot

A thin supply produces the same weak pilot flame as a clogged orifice. Several supply conditions can starve it, and different parties hold them.


A partly closed shutoff: The fireplace has its own shutoff valve upstream of the control valve. One turned partway during a cleaning or a log set change can feed a pilot too little gas to hold.


A low propane supply: On a propane system, a tank near empty can no longer hold the regulator's pressure, and a pilot that shrinks as the gauge gets low is a fuel question. The propane supplier handles the tank and its regulator.


A supply that cannot keep up: When the main burner opens, it draws more gas than the pilot. If the line, the regulator, or the supply feeding the fireplace cannot deliver both at once, pressure sags when the burner lights, and the pilot shrinks away from its sensor.


A problem on the utility side: The meter and the service regulator at the house belong to the gas company. When the fireplace pilot struggles at the same time as other gas appliances, such as a water heater pilot that also goes out or range burners that look weak, the fault may sit ahead of every appliance, and that call goes to the gas company.

The One Relight Attempt and When to Stop

A gas fireplace carries lighting instructions on a label attached to the appliance, or, on some units, on a plate or card near the controls behind the lower grille. Where the label is missing or unreadable, the pilot is left off. That label is the procedure for your valve, including the wait before relighting. Some valves will not allow a relight at all until the safety magnet has fully released, which is an interlock built into the valve.



Follow those instructions once. If the pilot will not hold after that single attempt, set the control to OFF and leave the fireplace off.

WARNING: Holding the control knob down to keep a pilot burning, or wedging it in place, defeats the one device that stops raw gas when the flame dies. A pilot that will not hold stays off until a gas technician finds the cause.

The same caution covers the parts themselves. Removing, bending, or cleaning the pilot assembly or the thermocouple is not a homeowner task, because disturbing the assembly can move the sensor out of the flame, and a loosened gas-side fitting could cause a leak.



A smell of gas changes everything above. Leave the house without touching light switches, phones, or the fireplace controls, and call the gas company from outside. A carbon monoxide alarm going off means the same exit: everyone out, and the call for help made from outside.

Testing Each Link in the Pilot Loop

A service visit works through the loop in order, starting with safety. The technician confirms there is no gas odor or leak at the appliance connections, then watches the pilot light and burn, reading the flame's color, shape, and where it lands on the sensor.



From there, the checks follow the chain. The sensor's position in the flame and its output are confirmed, and the valve's ability to hold on that output is checked. The pilot orifice and hood are inspected and cleaned, or replaced if fouled. Gas pressure is checked at the appliance with the burner both off and on, which is the test that distinguishes a sagging supply from a weak sensor. On a vented unit, the vent path and its termination are inspected, and the log and ember placement around the pilot hood are checked against the set's layout.


A failed thermocouple, thermopile, or pilot assembly is replaced with the part listed for that appliance. The fireplace is then run through a full cycle, pilot and main burner, to confirm the pilot holds.

TIP: The exact moment the pilot quit is the detail worth passing along when calling: on releasing the knob, after several minutes of burning, or when the main burner lit. That one observation narrows the search from the first minute.

Frequently Asked Questions

  • Should the fireplace gas shutoff be closed while the pilot is out?

    Setting the control knob to OFF stops gas at the fireplace's own valve, and closing the separate shutoff adds a second barrier while you wait for service. On a quarter-turn shutoff, a handle lying across the pipe is closed, and a handle lying along it is open. Reopening it comes before any relight by the label.

  • Could a blocked vent be what keeps shutting the pilot off?

    On some vented fireplaces and log sets, yes. A heat-sensing spill switch near the draft hood or vent collar is wired into the valve's control circuit, and when hot exhaust spills back into the room, it opens that circuit and the valve drops out just as if the flame had failed. Resetting or bypassing it silences the appliance's own device reporting the spillage, so a tripped spill switch indicates a venting problem that should be inspected.

  • Does the glass front matter on a sealed gas fireplace?

    On a direct-vent unit it does. The glass and its gasket close off the combustion chamber, which draws its air from outside through the vent. With the glass removed or a gasket leaking, room air enters the chamber, altering how the pilot and burner flames behave, so a direct-vent fireplace is never run with its glass off.

  • A new thermocouple went in, and the pilot still drops. What is left?

    The valve's magnet unit can weaken with age; on some valves, it is a separate part, while on others it comes only with a new valve. The connection where the sensor threads into the valve must also be clean and properly seated, since a loose or corroded connection loses current, just as a worn sensor does. A replacement sensor too short to reach its bracket properly causes the same symptom.

  • Why did the pilot start going out after the gas service was interrupted?

    When the supply is shut off at the meter, or a propane tank runs dry, air gets into the line. Until gas fully replaces it, a pilot can light weakly and then drop as pockets of air reach the orifice. After a propane run-out, the supplier checks the system for leaks before gas flows again; after a utility interruption, a single relight by the label applies, and a pilot that will not hold stays off.

  • Does the wall switch or remote control the pilot?

    On a standing-pilot millivolt system, it does not. The switch or remote opens and closes the main burner circuit, while the pilot is controlled only by the valve knob. A dead remote battery or a faulty wall switch cannot put out a standing pilot, and a main burner that will not come on while the pilot burns steadily is a separate fault in the switch, the thermopile, or the main valve.

Arrange gas log set repair for a pilot that keeps dropping out — pilot assembly diagnostics and thermocouple testing at the fireplace itself. Perfect Chimney Cleaning serves Greensboro, High Point, Winston-Salem. Call (336) 604-6711.

About the author

founded Perfect Chimney Cleaning in 2021 after twenty-one years in property management and real estate. Our inspections and repairs are led by CSIA-Certified Chimney Sweep Hannah Kendrick (#12553). Read more about our team.

Recent Posts

Inside a charred, circular pipe, looking up toward a bright opening above
By Yosef Hefetz • November 9, 2026
A dryer vented through the roof can collect lint on the climb, clog at the cap, and drip condensation. See what causes each problem and the signs to watch.
Brick chimneys on a shingled roof under a blue sky
By Yosef Hefetz • November 2, 2026
Short-term rental guests don't know your fireplace's habits. A host checklist for the sweep schedule, guest card, and alarms that keep it safe between stays.
Person in white coveralls working inside a fireplace opening in a living room.
By Yosef Hefetz • October 30, 2026
The smooth coat inside a smoke chamber does more than help the draft. Learn what parging is, how it fails, and why a breach is never cosmetic.
Cozy Christmas hearth with lit fireplace, decorated tree, wreath, and red ornaments
By Yosef Hefetz • October 23, 2026
A decorative fireplace in a restaurant or office stays tied to a live flue. See what disuse hides, who is responsible, and what belongs on file.
Brick chimney with soot stains above a shingled roof, topped by black vent caps.
By Yosef Hefetz • October 16, 2026
The machines next door shake the whole house. See how that energy reaches a chimney footing, and what a survey before the work establishes.
Attic under construction with exposed wooden beams, a brick chimney, blue insulation, and a window opening
By Yosef Hefetz • October 9, 2026
A chimney that drew fine for twenty years can change the weekend after the attic is sealed. What tightening the house does to the draft, and to the flue.
Modern dining room with dark table, silver chairs, large windows, and a white fireplace with a fire burning
By Yosef Hefetz • October 2, 2026
Thinking about swapping wood for gas logs or an insert? See what your fireplace and flue need to pass before that conversion happens.
Brick chimney with metal flashing on a gray shingle roof, showing cracked mortar at the base.
By Yosef Hefetz • September 30, 2026
Cold snaps don't just chill the air; they widen cracks in brick and mortar. Learn how freeze-thaw damage builds season after season and what stops it.
Open top-loading washing machine with a lint filter in a laundry room
By Yosef Hefetz • September 23, 2026
One load now takes two or three cycles to dry. Here's what usually causes it, and why ignoring it is a fire-safety issue, not just a nuisance.
Brick chimney above a shingled roof under a cloudy sky, with trees in the background
By Yosef Hefetz • September 16, 2026
A chalky white bloom on chimney brick is more than a surface stain. Learn what efflorescence is, why it forms, and when it flags a leak worth fixing fast.
Show More